Opening throttle cable

We advise you to measure your existing cable before ordering in case you have a non standard set up

 This part is available by special order, request a quote

 06117500 GU06117500 06 11 75 00
 0611 7500 0611.7500 06.11.75.00

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Sidestand cutout switch

See ELA81319 for rotary switch that was fitted to some models

 This part is available by special order, request a quote

 639542 MG639542

Fuel hose and clips to connect fuel filter to pump in fuel tank, worth fitting if the fuel hose keeps blowing off the filter on your bike

Fuel pipe and clip set. See FUA81000 for alternative part

 This part is available by special order, request a quote

 978219 MG978219

The innovative Stahlbus bleeder valve allows you to change the brake fluid yourself without assistance. Suitable for models with two bleed nipples per caliper

Linked Guzzi brake systems are notoriously tricky to bleed, this M6 auto bleed nipple can save you hours of tedious squeezing and pumping! This bleed nipple is slightly longer than the standard part so some thread will be left showing even when fully closed.

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÜV Rheinland.
  See BRA41652 for bleed valve cover

   More than 5 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Head gasket

 This part is available by special order, request a quote

 874621 MG874621

"The Carburettor Manual" is a comprehensive guide from Dellorto to the setting up and use of tapered needle motorcycle carburettors. Covers principle of operation of all Dellorto tapered needle carburettors 1970 onwards. 33 pages with colour pictures and diagrams. Also included is the original Dellorto "Tuning Guide 1.1" for carburettors, which gives advice on the choice, setting and use of a Dellorto tapered needle carburettor which includes colour carburettor cross sections showing the multiple stages of carburettor operation. Also contains float height and tapered needle selection tables.

 This part is due back in stock soon, call 01484 841395 to reserve yours

Front crankshaft oil seal

Viton seal

 3 in stock

90412237-Z

Little end or con rod bush

Also known as Guzzi ref. 91112128, 91112124, 91112127, 91112123, 91112122. Note that little end bushes may need reaming to suit your conrod and gudgeon pin

 1 in stock

 91112128 GU91112128 91 11 21 28
 9111 2128 9111.2128 91.11.21.28

Lightweight M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins). An aluminium filler plug made in Italy.

 1 in stock

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00